• 设为首页
  • 加入收藏
  • 联系邮箱
  • 网站首页
  • 期刊介绍
    • 期刊简介
    • 历任主编
    • 期刊荣誉
  • 编委会
    • 社长及主编
    • 主任委员
    • 编委名单
  • 投稿指南
    • 作者须知
    • 投稿步骤
    • 范文(规范细则)
    • 稿件处理流程
    • 著作权转让协议
  • 期刊影响力
  • 开放获取
  • 出版道德政策
    • 出版伦理声明
    • 学术不端认定和处理方法
    • 广告及市场推广
    • 同行评议流程
    • 斟误和撤回
    • 回避制度
    • 文章署名及版权转让
  • 历年目次
  • 联系我们
  • English
站内检索    
 
刘毅,刘振兴,李翠.一种新型模块化多电平换流器电平数倍增方法研究[J].电测与仪表,2019,56(8):30-35.
Liu Yi,Liu Zhenxing,Li Cui.Research on a new modular multilevel converter level multiplier method[J].Electrical Measurement & Instrumentation,2019,56(8):30-35.
一种新型模块化多电平换流器电平数倍增方法研究
Research on a new modular multilevel converter level multiplier method
DOI:
中文关键词:  模块化多电平换流器  子模块  最近电平调制  4N+1电平
英文关键词:modularized  multilevel converter, sub  module, nearest  level modulation, 4N+1 level
基金项目:国家自然科学基金项目(61174107,61471275)
        
作者中文名作者英文名单位
刘毅Liu Yi武汉科技大学
刘振兴Liu Zhenxing武汉科技大学
李翠Li Cui武汉科技大学
摘要点击次数: 1431
中文摘要:
      本文提出一种新型模块化多电平换流器拓扑结构。在传统模块化多电平拓扑结构基础上,将每个桥臂的一个常规子模块替换成3个新子模,新子模块电容值为常规子模块电容的2倍。并且提出相应的控制策略,新子模块电容电压为传统子模块电容电压的一半,可以将桥臂电压的电平数由N+1提高至2N+1。在此基础上采用改进型最近电平调制策略,最终将交流侧相电压电平等级提高至4N+1。在MATLAB/Simulink环境下,根据本文提出的拓扑结构和控制策略搭建系统仿真模型。仿真结果表明,本方法在子模块较多的情况下能有效降低硬件成本、提高供电质量。
英文摘要:
      A new modular multilevel converter topology is proposed in this paper. On the basis of traditional modular multilevel topology, a conventional sub module of each arm is replaced by 3 new sub modules, and the capacitance of the new sub module is 2 times of that of the conventional sub module capacitor. Then the corresponding control strategy is proposed. The capacitor voltage of the new sub module is half of the traditional sub module capacitor voltage, and the voltage level arm can be increased from N+1 to 2N+1. Besides, the improved Nearest Level Modulation strategy is adopted, the voltage level of the AC side phase is increased to 4N+1. Under the environment of MATLAB/Simulink, the system simulation model is built according to the topology and control strategy proposed in this paper. The simulation results show that this method can effectively reduce the cost of hardware and improve the quality of power supply in the case of MMC with a large number of sub modules.
查看全文  查看/发表评论  下载PDF阅读器
关闭
  • 哈尔滨电工仪表研究所有限公司
  • 中国电工仪器仪表信息网
  • 中国仪器仪表学会
  • 中华人民共和国新闻出版总署
  • 中国科技期刊编辑学会
  • 黑龙江省科学技术协会
  • 编辑之家
  • 中国知网
  • 万方数据库
  • 维普网
  • 北极星电力网
  • 中华中控网
  • 网站首页
  • 期刊介绍
    • 期刊简介
    • 历任主编
    • 期刊荣誉
  • 编委会
    • 社长及主编
    • 主任委员
    • 编委名单
  • 投稿指南
    • 作者须知
    • 投稿步骤
    • 范文(规范细则)
    • 稿件处理流程
    • 著作权转让协议
  • 期刊影响力
  • 开放获取
  • 出版道德政策
    • 出版伦理声明
    • 学术不端认定和处理方法
    • 广告及市场推广
    • 同行评议流程
    • 斟误和撤回
    • 回避制度
    • 文章署名及版权转让
  • 历年目次
  • 联系我们
地址:哈尔滨市松北区创新路2000号    邮编:150028
邮箱:dcyb@vip.163.com    电话:0451-86611021;87186023
© 2012 电测与仪表    哈公网监备2301003445号
黑ICP备11006624号-1
技术支持:北京勤云科技发展有限公司