• 设为首页
  • 加入收藏
  • 联系邮箱
  • 网站首页
  • 期刊介绍
    • 期刊简介
    • 历任主编
    • 期刊荣誉
  • 编委会
    • 社长及主编
    • 主任委员
    • 编委名单
  • 投稿指南
    • 作者须知
    • 投稿步骤
    • 范文(规范细则)
    • 稿件处理流程
    • 著作权转让协议
  • 期刊影响力
  • 开放获取
  • 出版道德政策
    • 出版伦理声明
    • 学术不端认定和处理方法
    • 广告及市场推广
    • 同行评议流程
    • 斟误和撤回
    • 回避制度
    • 文章署名及版权转让
  • 历年目次
  • 联系我们
  • English
站内检索    
 
葛腾飞,姜建国.同步电机矢量控制调速研究[J].电测与仪表,2020,57(16):1-5.
GE Tengfei,JIANG Jianguo.Research on Vector Control of Electric Excitation Synchronous Motor[J].Electrical Measurement & Instrumentation,2020,57(16):1-5.
同步电机矢量控制调速研究
Research on Vector Control of Electric Excitation Synchronous Motor
DOI:10.19753/j.issn1001-1390.2020.16.001
中文关键词:  三电平变换器  同步电动机  四段速度曲线  混合磁链观测模型
英文关键词:three-level converter  synchronous motor  four-stage speed curve  hybrid flux linkage observation model
基金项目:
     
作者中文名作者英文名单位
葛腾飞GE Tengfei上海交通大学 电子信息与电气工程学院
姜建国JIANG Jianguo上海交通大学 电子信息与电气工程学院
摘要点击次数: 957
中文摘要:
      电励磁同步电动机矢量控制技术是近几年研究的热点,而磁链观测模型是矢量控制技术的重要环节,合理配置磁链观测模型的系数是准确观测同步电机气隙磁链信息的关键。对于电流模型对电机参数敏感、电压模型存在积分初值偏差的问题,提出一种基于混合气隙磁链观测模型的三电平矢量控制方法。该方法不仅使系统能够在低速段使用开环电流模型,而且在中高速段使用自适应电压模型,同时还实现两个模型之间的平滑过渡。这使得该方法适合于在整个速度范围内精确观测出气隙磁链。四段速度曲线使提升机的整个行程更加平稳。利用MATLAB软件及实验平台对该控制策略进行了仿真和相关实验研究,结果验证了所采用控制方法的有效性。
英文摘要:
      The vector control technology of electrically excited synchronous motor is a hotspot in recent years, and the flux linkage observation model is an important part of vector control technology. Reasonable configuration of the flux linkage observation model coefficient is the key to accurately observe the air gap flux linkage information of synchronous motor. A vector control method based on hybrid air gap flux observation model is proposed to solve the problems of sensitive current model to motor parameters and integral initial value deviation. The method not only enables the system to use the current model in the low speed section, but also uses the voltage model in the high and medium speed sections. At the same time, it realizes a smooth transition of the two models so that the whole model is suitable for accurately observing the air gap flux linkage in the full speed range. The MATLAB software and experimental platform are used to simulate and experimentally study the proposed hybrid air gap flux linkage method. The effectiveness of the proposed control method was verified by the results of the simulation and the experiment.
查看全文  查看/发表评论  下载PDF阅读器
关闭
  • 哈尔滨电工仪表研究所有限公司
  • 中国电工仪器仪表信息网
  • 中国仪器仪表学会
  • 中华人民共和国新闻出版总署
  • 中国科技期刊编辑学会
  • 黑龙江省科学技术协会
  • 编辑之家
  • 中国知网
  • 万方数据库
  • 维普网
  • 北极星电力网
  • 中华中控网
  • 网站首页
  • 期刊介绍
    • 期刊简介
    • 历任主编
    • 期刊荣誉
  • 编委会
    • 社长及主编
    • 主任委员
    • 编委名单
  • 投稿指南
    • 作者须知
    • 投稿步骤
    • 范文(规范细则)
    • 稿件处理流程
    • 著作权转让协议
  • 期刊影响力
  • 开放获取
  • 出版道德政策
    • 出版伦理声明
    • 学术不端认定和处理方法
    • 广告及市场推广
    • 同行评议流程
    • 斟误和撤回
    • 回避制度
    • 文章署名及版权转让
  • 历年目次
  • 联系我们
地址:哈尔滨市松北区创新路2000号    邮编:150028
邮箱:dcyb@vip.163.com    电话:0451-86611021;87186023
© 2012 电测与仪表    哈公网监备2301003445号
黑ICP备11006624号-1
技术支持:北京勤云科技发展有限公司