• 设为首页
  • 加入收藏
  • 联系邮箱
  • 网站首页
  • 期刊介绍
    • 期刊简介
    • 历任主编
    • 期刊荣誉
  • 编委会
    • 社长及主编
    • 主任委员
    • 编委名单
  • 投稿指南
    • 作者须知
    • 投稿步骤
    • 范文(规范细则)
    • 稿件处理流程
    • 著作权转让协议
  • 期刊影响力
  • 开放获取
  • 出版道德政策
    • 出版伦理声明
    • 学术不端认定和处理方法
    • 广告及市场推广
    • 同行评议流程
    • 斟误和撤回
    • 回避制度
    • 文章署名及版权转让
  • 历年目次
  • 联系我们
  • English
站内检索    
 
艾小清,袁旭峰,熊炜,徐玉韬,谈竹奎,赵真.柔直配电系统混合型MMC可靠性评估[J].电测与仪表,2023,60(9):88-95.
Ai Xiaoqing,Yuan Xufeng,Xiong Wei,Xu Yutao,Tan Zhukui,Zhao Zhen.Reliability evaluation of hybrid MMC for flexible DC distribution system[J].Electrical Measurement & Instrumentation,2023,60(9):88-95.
柔直配电系统混合型MMC可靠性评估
Reliability evaluation of hybrid MMC for flexible DC distribution system
DOI:10.19753/j.issn1001-1390.2023.09.013
中文关键词:  柔性直流配电系统  混合型MMC  故障树  冗余配置  可靠性建模
英文关键词:flexible DC distribution system, hybrid MMC, fault tree, redundant configuration, reliability modeling
基金项目:国家自然科学基金项目( 51667007)
                 
作者中文名作者英文名单位
艾小清Ai Xiaoqing贵州大学 电气工程学院,贵阳 550025
袁旭峰Yuan Xufeng贵州大学 电气工程学院,贵阳 550025
熊炜Xiong Wei贵州大学 电气工程学院,贵阳 550025
徐玉韬Xu Yutao贵州电网有限公司电力科学研究院,贵阳 550002
谈竹奎Tan Zhukui贵州电网有限公司电力科学研究院,贵阳 550002
赵真Zhao Zhen贵州大学 电气工程学院,贵阳 550025
摘要点击次数: 1599
中文摘要:
      模块化多电平换流器(Modular Multilevel Converter, MMC) 作为柔性直流配电系统中的关键设备直接关系到整个配电系统的安全可靠,因此有必要对其可靠性进行评估。对半桥、全桥以及混合型MMC进行比较分析,对比得出混合型MMC更适合运用柔直配电系统。通过对MMC工作原理、直流阻断能力、冗余配置的阐述计算出了全桥、半桥模块数及比例;建立元件可靠性模型,并运用故障树法对混合型MMC进行了可靠性建模。利用MATLAB针对冗余配置、全桥、半桥子模块比例、IGBT结温及损耗进行算例分析,得出结论:合理的冗余配置以及全桥、半桥比例是设计混合型MMC的关键所在。同时指出了IGBT的运行工况会导致混合型MMC的故障率提升。
英文摘要:
      As a key device in flexible DC distribution system, the modular multilevel converter (MMC) is directly related to the security and reliability of the whole power distribution system, so it is necessary to evaluate its reliability. In this paper, half, full bridge and mixed MMC are compared and analyzed, and the mixed MMC is more suitable for flexible direct distribution system. The full and half bridge module number and proportion is calculated through the MMC working principle, DC blocking capacity, redundant configuration. The component reliability modeling is established and the fault tree method is used to model the reliability of hybrid MMC. MATLAB is used to analyze the redundancy configuration, full and half bridge sub-module ratio, IGBT junction temperature and loss, and the conclusion is drawn that reasonable redundancy configuration and full and half bridge ratio are the key to the design of hybrid MMC. It is also pointed out that the operation condition of IGBT will lead to the increase of the failure rate of hybrid MMC.
查看全文  查看/发表评论  下载PDF阅读器
关闭
  • 哈尔滨电工仪表研究所有限公司
  • 中国电工仪器仪表信息网
  • 中国仪器仪表学会
  • 中华人民共和国新闻出版总署
  • 中国科技期刊编辑学会
  • 黑龙江省科学技术协会
  • 编辑之家
  • 中国知网
  • 万方数据库
  • 维普网
  • 北极星电力网
  • 中华中控网
  • 网站首页
  • 期刊介绍
    • 期刊简介
    • 历任主编
    • 期刊荣誉
  • 编委会
    • 社长及主编
    • 主任委员
    • 编委名单
  • 投稿指南
    • 作者须知
    • 投稿步骤
    • 范文(规范细则)
    • 稿件处理流程
    • 著作权转让协议
  • 期刊影响力
  • 开放获取
  • 出版道德政策
    • 出版伦理声明
    • 学术不端认定和处理方法
    • 广告及市场推广
    • 同行评议流程
    • 斟误和撤回
    • 回避制度
    • 文章署名及版权转让
  • 历年目次
  • 联系我们
地址:哈尔滨市松北区创新路2000号    邮编:150028
邮箱:dcyb@vip.163.com    电话:0451-86611021;87186023
© 2012 电测与仪表    哈公网监备2301003445号
黑ICP备11006624号-1
技术支持:北京勤云科技发展有限公司